Echo SRM - 2601 Manual de usuario

Grass Trimmer/Brush CutterOperator's ManualMODELS, SRM - 2601SRM - 2610Serial Number 001001 & UpWARNING DANGER WARNING The engin

10Contents ListItemsMODELS2610 1E2601 1E√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√√1 - Power Head1 - Drive Shaft Assembly1 - Plastic Bag (co-pa

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL11EMISSION CONTROL --The emission control system for this engine is EM (EngineModification).Emission C

121. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place forfuture reference, i.e., operation,

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL13SPECIFICATIONSMODELSRM-2601 1ESRM-2610 1ELength1800 mm (70.9 in.)1800 mm (70.9 in.)Width315 mm (12

14ASSEMBLYDRIVE SHAFT/POWER HEADTools Required: 4 mm Hex WrenchParts Required: Power head, Drive shaft Assembly1. Loosen, the bolt (A) at engine drive

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL15BAPLASTIC SHIELD INSTALLATION(for Nylon Line Operation)Tools Required: Screwdriver.Parts Required: P

16NOTEFor SRM-2610 handle assembly refer to "U-Handle Installationpage 18 instructions 1, 10, 12 - 16.ACCESSORY INSTALLATIONBlade Conversion Kit

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL17INSTALL METAL SHIELDTools Required: 8mm x 10mm Open End Wrench, Screwdriver.Parts Required: Metal

18U-HANDLE INSTALLATIONTools Required: 8mm x 10mm Open End Wrench, Screwdriver, 3mmand 4mm Hex Wrench, PliersParts Required: U-Handle/Blade Conversion

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL1912. Route throttle linkage and ignition lead assembly around front ofU-Handle bracket and clip to dr

2INTRODUCTIONWelcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and

20PRE - OPERATIONOPERATION WITH BLADESPreparing the Trimmer/Brush Cutter for Blade UseWARNING DANGERBlade use DEMANDS specific Brush Cutter config

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL21Choosing the Correct BladeWARNING DANGERThe type of Blade used MUST be matched to the type and s

22FUELFuel RequirementsGasoline - Use 89 Octane [ ] (mid grade or higher) gasoline orgasohol known to be good quality. Gasohol may contain up t

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL23After Refueling;• Wipe any spilled fuel from the unit.• Move at least 3 M (10 ft.) from refueling lo

24DETERMINE OPERATION AREAWARNING DANGERInspect starting area for hazards such as rocks, glass, debris etc.which could be contacted by the cutting

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL252. Close Choke - Cold Start.Move choke lever (B) to Cold Start Position.3. Primer - Pump Bulb.Pump p

262. Primer - Pump Bulb. Pump primer bulb (C) until fuel is visiblein the "Clear" fuel return line (D).3. Start - Pull Rope. Lay the trimm

RECORTADORA DE HIERBA/CORTADORA DE MALEZAMANUAL DEL OPERADOR27INTERVALOS DE MANTENIMIENTO/etnenopmoCametsiSedotneimidecorPotneiminetnaMsairaseceNedlev

28WARNING DANGERFuel is VERY flammable. Use extreme care when mixing, storing orhandling.1. Use a clean rag to remove loose dirt from around fuel

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL29SPARK PLUGLevel 2.Tools Required: T-Wrench (combination socket wrench & screw driversupplied wi

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL3This symbol accompanied by the words WARNING andDANGER calls attention to an act or condition that c

301. Remove air filter cover (A).2. Remove spark plug lead.3. Remove two (2) muffler cover screws and muffler cover (B).4. Remove screw and arm rest (

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL311. Remove engine cover (A). See “Cleaning Cooling System” pages29 & 30 for step by step instruct

32ALUBRICATIONLevel 1.Tools Required: 8 mm Open End Wrench, Screwdriver, Clean Rag.Parts Required: Lithium Base Grease.Gear Housing1. Clean all loos

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL333. Hold the spool, opening toward you. Place index finger betweenthe two strands and wind line, tig

34SHARPENING METAL BLADESThree styles of metal blades are approved for use on the ECHO BrushCutter. The 8-tooth blade can be sharpened during normal

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL35TROUBLESHOOTINGProblemEngine -- starts hardEngine -- does not startCauseRemedyEngineCranksFuel atcar

36STORAGELong Term Storage (over 30 days)WARNING DANGERDuring operation the muffler or catalytic muffler and surrounding cover become hot. Always

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL37NOTES

38NOTES

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL39NOTES

4INTERNATIONAL SYMBOLSShaft DecalWARNING DANGER• This unit can be dangerous and cause serious injury if improperlyused. To reduce injury ri

ECHO, INCORPORATED400 OAKWOOD R OADLAKE Z URICH, IL 60047DEALER?Call1-800-432-ECHO1-800-432-3246ECHO Incorporated400 Oakwood RoadLake Zurich, IL 600

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL5EQUIPMENTWARNING DANGER• Use only ECHO approved attachments. Serious injury may resultfrom the us

6FUELWARNING DANGERFuel is VERY flammable. Use extreme care when mixing, storing orhandling, otherwise serious personal injury may result.• Use a

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL7Physical Condition --Your judgment and physical dexterity may not be good:• if you are tired or sick,

8SAFE OPERATIONDetermine Operation Area• Provide all operators of this equipment with the Operator's Manualand instructions for safe operation.•

GRASS TRIMMER/BRUSH CUTTEROPERATOR'S MANUAL9EXTENDED OPERATION/EXTREME CONDITIONSVibration and ColdIt is believed that a condition called Raynaud